Home | | Design of Transmission Systems | Gear Terminology

Chapter: Mechanical : Design of Transmission Systems : Spur Gears and Parallel Axis Helical Gears

Gear Terminology

The following terms, which will be mostly used in this chapter, should be clearly understood at this stage.

Gear Terminology

 

The following terms, which will be mostly used in this chapter, should be clearly understood at this stage.

 

1. Pitch circle. It is an imaginary circle which by pure rolling action, would give the same motion as the actual gear

 

2. Pitch circle diameter. It is the diameter of the pitch circle. The size of the gear is usually specified by the pitch circle diameter. It is also called as pitch diameter.

 

3. Pitch point. It is a common point of contact between two pitch circles.

 

4. Pitch surface. It is the surface of the rolling discs which the meshing gears have replaced at the pitch circle.

 

5. Pressure angle or angle of obliquity. It is the angle between the common normal to two

 

gear teeth at the point of contact and the common tangent at the pitch point. It is usually denoted by φ. The standard pressure angles are 1 14 /2° and 20°.

 

6. Addendum. It is the radial distance of a tooth from the pitch circle to the top of the tooth.

 

7.  Dedendum. It is the radial distance of a tooth from the pitch circle to the bottom of the tooth.

 

8. Addendum circle. It is the circle drawn through the top of the teeth and is concentric with the pitch circle.

 

9. Dedendum circle. It is the circle drawn through the bottom of the teeth. It is also called

root circle.

Note : Root circle diameter = Pitch circle diameter × cos φ, where φ is the pressure angle.

 

10. Circular pitch. It is the distance measured on the circumference of the pitch circle from a point of one tooth to the corresponding point on the next tooth. It is usually denoted by pc. Mathematically,

 

Circular pitch, pc = π D/T

 

Where,        D = Diameter of the pitch circle, and

T = Number of teeth on the wheel.

A little consideration will show that the two gears will mesh together correctly, if the

two wheels have the same circular pitch.

Note : If D1 and D2 are the diameters of the two meshing gears having the teeth T1 and T2 respectively; then for them to mesh correctly,

 


 

11.Diametral pitch. It is the ratio of number of teeth to the pitch circle diameter in millimetres. It denoted by pd. Mathematically,

 

Diametral pitch,

 

                                                                                     

where                                                      T = Number of teeth, and

                                                                D = Pitch circle diameter.

 

12. Module. It is the ratio of the pitch circle diameter in millimetres to the number of teeth. It is usually denoted by m. Mathematically,

 

Module, m = D / T

 

Note : The recommended series of modules in Indian Standard are 1, 1.25, 1.5, 2, 2.5, 3, 4, 5, 6, 8, 10, 12, 16, 20, 25, 32, 40 and 50.

 

The modules 1.125, 1.375, 1.75, 2.25, 2.75, 3.5, 4.5,5.5, 7, 9, 11, 14, 18, 22, 28, 36 and 45 are of second choice.

 

13.                                                                                                                                                   Clearance. It is the radial distance from the top of the tooth to the bottom of the tooth, in a meshing gear. A circle passing through the top of the meshing gear is known as clearance circle.

 

14.                                                                                                                                                   Total depth. It is the radial distance between the addendum and the dedendum circle of a gear. It is equal to the sum of the addendum and dedendum.

 

15.Working depth. It is radial distance from the addendum circle to the clearance circle. It is equal to the sum of the addendum of the two meshing gears.

 

16.                                                                                                                                                   Tooth thickness. It is the width of the tooth measured along the pitch circle.

 

17.Tooth space. It is the width of space between the two adjacent teeth measured along the pitch circle.

 

18.  Backlash. It is the difference between the tooth space and the tooth thickness, as measured on the pitch circle.

 

19.                                                                                                                                                   Face of the tooth. It is surface of the tooth above the pitch surface.

 

20.                                                                                                                                                   Top land. It is the surface of the top of the tooth.

 

21.                                                                                                                                                   Flank of the tooth. It is the surface of the tooth below the pitch surface.

 

22.Face width. It is the width of the gear tooth measured parallel to its axis.

 

 

23.                                                                                                                                                   Profile. It is the curve formed by the face and flank of the tooth.

 

24.                                                                                                                                                   Fillet radius. It is the radius that connects the root circle to the profile of the tooth.

 

25. Path of contact. It is the path traced by the point of contact of two teeth from the beginning to the end of engagement.

 

26. Length of the path of contact. It is the length of the common normal cut-off by the addendum circles of the wheel and pinion.

 

27.Arc of contact. It is the path traced by a point on the pitch circle from the beginning to the end of engagement of a given pair of teeth. The arc of contact consists of two parts, i.e.

 

(a) Arc of approach. It is the portion of the path of contact from the beginning of the engagement

 

to the pitch point.

(b) Arc of recess. It is the portion of the path of contact from the pitch point to the end of the engagement of a pair of teeth.

 

Note: The ratio of the length of arc of contact to the circular pitch is known as contact ratio i.e. number of pairs of teeth in contact.

 

Study Material, Lecturing Notes, Assignment, Reference, Wiki description explanation, brief detail
Mechanical : Design of Transmission Systems : Spur Gears and Parallel Axis Helical Gears : Gear Terminology |


Privacy Policy, Terms and Conditions, DMCA Policy and Compliant

Copyright © 2018-2023 BrainKart.com; All Rights Reserved. Developed by Therithal info, Chennai.