Home | | Electronic Devices and Circuits | TRIAC: symbol, basics, Operation, Characteristics, Advantages and disadvantages

Chapter: Electronic Devices and Circuits : Transistors

TRIAC: symbol, basics, Operation, Characteristics, Advantages and disadvantages

The TRIAC is a three terminal semiconductor device for controlling current. It gains its name from the term TRIode for Alternating Current.

TRIAC

 

The TRIAC is a three terminal semiconductor device for controlling current. It gains its name from the term TRIode for Alternating Current.

 

It is effectively a development of the SCR or thyristor, but unlike the thyristor which is only able to conduct in one direction, the TRIAC is a bidirectional device.

 

Ø         TRIAC symbol

 

The circuit symbol recognises the way in which the TRIAC operates. Seen from the outside it may be viewed as two back to back thyristors and this is what the circuit symbol indicates.


 

On the TRIAC symbol there are three terminals. These are the Gate and two other terminals are often referred to as an "Anode" or "Main Terminal". As the TRIAC has two of these they are labelled either Anode 1 and Anode 2 or Main Terminal, MT1 and MT2.

 

Ø         TRIAC basics

 

The TRIAC is a component that is effectively based on the thyristor. It provides AC switching for electrical systems. Like the thyristor, the TRIACs are used in many electrical switching applications. They find particular use for circuits in light dimmers, etc., where they enable both halves of the AC cycle to be used.

 

This makes them more efficient in terms of the usage of the power available. While it is possible to use two thyristors back to back, this is not always cost effective for low cost and relatively low power applications.

 

 

It is possible to view the operation of a TRIAC in terms of two thyristors placed back to back.


 

One of the drawbacks of the TRIAC is that it does not switch symmetrically. It will often have an offset, switching at different gate voltages for each half of the cycle. This creates additional harmonics which is not good for EMC performance and also provides an imbalance in the system

 

 

In order to improve the switching of the current waveform and ensure it is more symmetrical is to use a device external to the TRIAC to time the triggering pulse. A DIAC placed in series with the gate is the normal method of achieving this.



Ø          Operation

 

With switch S open, there will be no gate current and the triac is cut off. Even with no current the triac can be turned on provided the supply voltage becomes equal to the breakover voltage.

 

When switch S is closed, the gate current starts flowing in the gate circuit. Breakover voltage of triac can be varied by making proper currnt flow. Triac starts to conduct wheather MT2 is positive or negative w.r.t MT1.


 

If terminal MT2 is positive w.r.t MT1 the TRIAC is on and the conventional current will flow from MT2 to MT1. If terminal MT2 is negative w.r.t MT1 the TRIAC is again turned on and the conventional current will flow from MT1 to MT2.

 

Ø          Characteristics

 


 

 

The V-I curve for triac in the Ist and IIIrd quadrants are essentially identical to SCR in the Ist quadrant. The triac can be operated with either positive or negative gate control voltage but in normal operation usually the gate voltage is positive in quadrant I and negative in quadrant III. The supply voltage at which the triac is ON depends upon gate current. The greater gate current and smaller supply voltage at which triac is turned on. This permits to use triac to control a,c. power in a load from zero to full power in a smooth and continuous manner with no loss in the controlling device.

 

Ø         Advantages and disadvantages

 

When requiring to switch both halves of an AC waveform there are two options that are normally considered. One is to use a TRIAC, and the other is to use two thyristors connected back to back - one thyristor is used to switch one half of the cycle and the second connected in the reverse direction operates on the other half cycle.As there are two options the advantages and disadvantages of using a TRIAC must be weighed up.


Ø         Advantages

 

Can switch both halves of an AC waveform

 

Single component can be used for full AC switching

 

Ø         Disadvantages

A TRIAC does not fire symmetrically on both sides of the waveform

 

Switching gives rise to high level of harmonics due to non-symmetrical switching

 

More susceptible to EMI problems as a result of the non-symmetrical switching

 

Care must be taken to ensure the TRIAC turns off fully when used with inductive loads.

 

 

Ø         Applications

 

TRIACs are used in a number of applications. However they tend not to be used in high power switching applications - one of the reasons for this is the non-symmetrical switching characteristics. For high power applications this creates a number of difficulties, especially with electromagnetic interference.

 

However TRIACs are still used for many electrical switching applications:

ü        Domestic light dimmers

 

ü        Electric fan speed controls

 

ü        Small motor controls

 

ü        Control of small AC powered domestic appliances

Study Material, Lecturing Notes, Assignment, Reference, Wiki description explanation, brief detail
Electronic Devices and Circuits : Transistors : TRIAC: symbol, basics, Operation, Characteristics, Advantages and disadvantages |


Privacy Policy, Terms and Conditions, DMCA Policy and Compliant

Copyright © 2018-2024 BrainKart.com; All Rights Reserved. Developed by Therithal info, Chennai.